LUXON 4-POST RUBBER ISOLATED 1 1/8" BAR MOUNTS DUCATI DESMO450 MX/EDX 2026 CONE INTERFACE
Luxon lightweight 4-post bar mounts eliminate twisting due to small crashes and tip-overs without sacrificing vibration absorption like a solid mount would. Four sets of bushings absorb hard hits and track roughness without compromising steering precision. Three different rubber bushing sets (soft, medium, and firm) are included to fine tune the feel.
These mounts fit stock Ducati triple clamps with the rubber cone interface, which includes many Ducati motocross and off-road models. The mounts will work in both the forward and back triple clamp mount hole locations and are the stock offset (8mm of bar position change when flipping the mounts around). Height is the same as stock (28mm high, bottom of bar to top of triple clamp).
Kit Includes:
- Rubber isolated lower bar mounts
- Rubber bushings
- Upper bar clamps
- High-strength steel clamp bolts
- Anti-seize
- Instruction manual.
Three different hardness levels of rubber bushings are included at no additional cost. Soft (green) is for lighter riders, vet riders, or those with wrist injuries. Medium (yellow) is recommended for most off-road and motocross use, and hard (red) is recommended for aggressive motocross use and faster riders. It is also possible to mix different hardness levels of top and bottom bushings (for example, medium uppers with hard lowers) for further tuning.
Bushings will "break in" on the first ride and become a little softer than when first installed. Like all rubber bushings, these are wear items and will eventually break down and need replacing. Softer bushings will need to be replaced more often than harder bushings. Replacement bushings areĀ available here.
Depending on the installation type, make and model of bike, bar mount position, etc., you may need to lightly trim plastic brackets and/or relocate hour meters or accessories to allow clearance for these bar mounts in some mount positions (typically not an issue on motocross bike installations). Always check for full clearance after installation and before riding.
BAR SIZE:
Luxon 1 1/8" bar mounts fit standard 1 1/8" (28.6 mm) handlebars (sometimes called fatbars) and Luxon 36mm mounts fit theĀ Renthal FB36 bars (36 mm). These are NOT the same as fatbars, they have a much larger clamping diameter. Luxon do not offer bar mounts to fit the old 7/8" size handlebars. Other aftermarket companies offer adapter bushings to fit the 7/8" bar diameter in standard 1 1/8" mounts if necessary.
If you require 36mm bar mounts - click here.
SPECIFICATIONS
WEIGHT (1 1/8") 429 g, 0.95 lbs
WEIGHT (36 MM) 461 g, 1.02 lbs
STOCK WEIGHT (2026 model) 354 g, 0.78 lbs
BIKE FITMENT
DUCATI
- DESMO250 MX 2027
- DESMO450 MX 2026
- DESMO450 EDX 2026
These mounts fit stock Ducati triple clamps with the rubber cone interface, which includes many Ducati motocross and off-road models.
The Ducati Cone interface is a tapered cone shaped hole on the top and bottom of the triple clamp (a cross section would look like an hour glass). Newer stock triple clamps have two sets of holes for position adjustment; our bar mounts fit both hole positions.
Image Above:Ā The Ducati Cone interface on a stock clamp
ADDITIONAL INFORMATION
Product Information
Product Information
Shipping & Returns
Shipping & Returns
LUXON 4-POST RUBBER ISOLATED 1 1/8" BAR MOUNTS DUCATI DESMO450 MX/EDX 2026 CONE INTERFACE
LUXON 4-POST RUBBER ISOLATED 1 1/8" BAR MOUNTS DUCATI DESMO450 MX/EDX 2026 CONE INTERFACE
Luxon lightweight 4-post bar mounts eliminate twisting due to small crashes and tip-overs without sacrificing vibration absorption like a solid mount would. Four sets of bushings absorb hard hits and track roughness without compromising steering precision. Three different rubber bushing sets (soft, medium, and firm) are included to fine tune the feel.
These mounts fit stock Ducati triple clamps with the rubber cone interface, which includes many Ducati motocross and off-road models. The mounts will work in both the forward and back triple clamp mount hole locations and are the stock offset (8mm of bar position change when flipping the mounts around). Height is the same as stock (28mm high, bottom of bar to top of triple clamp).
Kit Includes:
- Rubber isolated lower bar mounts
- Rubber bushings
- Upper bar clamps
- High-strength steel clamp bolts
- Anti-seize
- Instruction manual.
Three different hardness levels of rubber bushings are included at no additional cost. Soft (green) is for lighter riders, vet riders, or those with wrist injuries. Medium (yellow) is recommended for most off-road and motocross use, and hard (red) is recommended for aggressive motocross use and faster riders. It is also possible to mix different hardness levels of top and bottom bushings (for example, medium uppers with hard lowers) for further tuning.
Bushings will "break in" on the first ride and become a little softer than when first installed. Like all rubber bushings, these are wear items and will eventually break down and need replacing. Softer bushings will need to be replaced more often than harder bushings. Replacement bushings areĀ available here.
Depending on the installation type, make and model of bike, bar mount position, etc., you may need to lightly trim plastic brackets and/or relocate hour meters or accessories to allow clearance for these bar mounts in some mount positions (typically not an issue on motocross bike installations). Always check for full clearance after installation and before riding.
BAR SIZE:
Luxon 1 1/8" bar mounts fit standard 1 1/8" (28.6 mm) handlebars (sometimes called fatbars) and Luxon 36mm mounts fit theĀ Renthal FB36 bars (36 mm). These are NOT the same as fatbars, they have a much larger clamping diameter. Luxon do not offer bar mounts to fit the old 7/8" size handlebars. Other aftermarket companies offer adapter bushings to fit the 7/8" bar diameter in standard 1 1/8" mounts if necessary.
If you require 36mm bar mounts - click here.
SPECIFICATIONS
WEIGHT (1 1/8") 429 g, 0.95 lbs
WEIGHT (36 MM) 461 g, 1.02 lbs
STOCK WEIGHT (2026 model) 354 g, 0.78 lbs
BIKE FITMENT
DUCATI
- DESMO250 MX 2027
- DESMO450 MX 2026
- DESMO450 EDX 2026
These mounts fit stock Ducati triple clamps with the rubber cone interface, which includes many Ducati motocross and off-road models.
The Ducati Cone interface is a tapered cone shaped hole on the top and bottom of the triple clamp (a cross section would look like an hour glass). Newer stock triple clamps have two sets of holes for position adjustment; our bar mounts fit both hole positions.
Image Above:Ā The Ducati Cone interface on a stock clamp
ADDITIONAL INFORMATION
Original: $214.35
-65%$214.35
$75.02Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Luxon lightweight 4-post bar mounts eliminate twisting due to small crashes and tip-overs without sacrificing vibration absorption like a solid mount would. Four sets of bushings absorb hard hits and track roughness without compromising steering precision. Three different rubber bushing sets (soft, medium, and firm) are included to fine tune the feel.
These mounts fit stock Ducati triple clamps with the rubber cone interface, which includes many Ducati motocross and off-road models. The mounts will work in both the forward and back triple clamp mount hole locations and are the stock offset (8mm of bar position change when flipping the mounts around). Height is the same as stock (28mm high, bottom of bar to top of triple clamp).
Kit Includes:
- Rubber isolated lower bar mounts
- Rubber bushings
- Upper bar clamps
- High-strength steel clamp bolts
- Anti-seize
- Instruction manual.
Three different hardness levels of rubber bushings are included at no additional cost. Soft (green) is for lighter riders, vet riders, or those with wrist injuries. Medium (yellow) is recommended for most off-road and motocross use, and hard (red) is recommended for aggressive motocross use and faster riders. It is also possible to mix different hardness levels of top and bottom bushings (for example, medium uppers with hard lowers) for further tuning.
Bushings will "break in" on the first ride and become a little softer than when first installed. Like all rubber bushings, these are wear items and will eventually break down and need replacing. Softer bushings will need to be replaced more often than harder bushings. Replacement bushings areĀ available here.
Depending on the installation type, make and model of bike, bar mount position, etc., you may need to lightly trim plastic brackets and/or relocate hour meters or accessories to allow clearance for these bar mounts in some mount positions (typically not an issue on motocross bike installations). Always check for full clearance after installation and before riding.
BAR SIZE:
Luxon 1 1/8" bar mounts fit standard 1 1/8" (28.6 mm) handlebars (sometimes called fatbars) and Luxon 36mm mounts fit theĀ Renthal FB36 bars (36 mm). These are NOT the same as fatbars, they have a much larger clamping diameter. Luxon do not offer bar mounts to fit the old 7/8" size handlebars. Other aftermarket companies offer adapter bushings to fit the 7/8" bar diameter in standard 1 1/8" mounts if necessary.
If you require 36mm bar mounts - click here.
SPECIFICATIONS
WEIGHT (1 1/8") 429 g, 0.95 lbs
WEIGHT (36 MM) 461 g, 1.02 lbs
STOCK WEIGHT (2026 model) 354 g, 0.78 lbs
BIKE FITMENT
DUCATI
- DESMO250 MX 2027
- DESMO450 MX 2026
- DESMO450 EDX 2026
These mounts fit stock Ducati triple clamps with the rubber cone interface, which includes many Ducati motocross and off-road models.
The Ducati Cone interface is a tapered cone shaped hole on the top and bottom of the triple clamp (a cross section would look like an hour glass). Newer stock triple clamps have two sets of holes for position adjustment; our bar mounts fit both hole positions.
Image Above:Ā The Ducati Cone interface on a stock clamp
